someone is watching. It simply indicates that the camera has power and is functioning properly. The blue light is a helpful visual indicator to let you know that the camera is active and ready to capture any motion or activity in its field of view.
How do I stop my Ring light from flashing In the case of the Ring Floodlight, the blinking is most likely caused by a dying battery. If you are having this problem, charging the battery should solve it. The sensor’s sensitivity can be adjusted so that a dog strolling around the yard won’t set off the floodlights, but a person walking up to the house will.
Why is the blue and white light flashing on my Ring camera Blue or white flashing from the setup light can be an indicator of a device action such as setup mode or an update. The best step is to check your Ring app to see if you have a good RSSI, or signal strength, in the Device Health section for your camera. How do I reset my Ring motion light If the light on your Floodlight Cam does not light up and flash and your Floodlight Cam is wired correctly and is receiving power, you can try performing a hard reset. Hold down the top button for a full 30 seconds. Why does my Ring light keep turning on with no motion Check your batteries. Check the area around the Motion Sensor. There may be something in the area (like a small animal) that is triggering your sensor. Check your motion sensitivity controls in the Ring app. Why does my floodlight flicker LED flood lights may flicker if there are voltage changes in the fixture’s wiring. Current fluctuations are often to blame for the occasional flickering or flashing of an LED flood light. If your flood lights flicker when another appliance or electrical system is in use, a voltage fluctuation is likely to blame. Where is the reset button on the ring floodlight Locate the reset button atop the camera. Press and hold the reset button for 30 seconds. After releasing it, the status light located at the bottom will flash a few times indicating the camera is restarting. The camera settings are now restored to its factory defaults. Why is the blue light blinking on my security camera A blinking blue light indicates that the camera has lost connection to the Internet and is trying to reconnect. A red light indicates that the camera has been factory reset and is in pairing mode. Was this article helpful Does the blue light on Ring camera mean someone is watching The blue light on your Ring camera is not an indication that someone is watching. It simply indicates that the camera has power and is functioning properly. The blue light is a helpful visual indicator to let you know that the camera is active and ready to capture any motion or activity in its field of view. 
How do I stop my Ring light from flashing
In the case of the Ring Floodlight, the blinking is most likely caused by a dying battery. If you are having this problem, charging the battery should solve it. The sensor's sensitivity can be adjusted so that a dog strolling around the yard won't set off the floodlights, but a person walking up to the house will.
Cached
Why is the blue and white light flashing on my Ring camera
Blue or white flashing from the setup light can be an indicator of a device action such as setup mode or an update. The best step is to check your Ring app to see if you have a good RSSI, or signal strength, in the Device Health section for your camera.
How do I reset my Ring motion light
If the light on your Floodlight Cam does not light up and flash and your Floodlight Cam is wired correctly and is receiving power, you can try performing a hard reset. Hold down the top button for a full 30 seconds.
Why does my Ring light keep turning on with no motion
Check your batteries. Check the area around the Motion Sensor. There may be something in the area (like a small animal) that is triggering your sensor. Check your motion sensitivity controls in the Ring app.
Why does my floodlight flicker
LED flood lights may flicker if there are voltage changes in the fixture's wiring. Current fluctuations are often to blame for the occasional flickering or flashing of an LED flood light. If your flood lights flicker when another appliance or electrical system is in use, a voltage fluctuation is likely to blame.
Where is the reset button on the ring floodlight
Locate the reset button atop the camera. Press and hold the reset button for 30 seconds. After releasing it, the status light located at the bottom will flash a few times indicating the camera is restarting. The camera settings are now restored to its factory defaults.
Why is the blue light blinking on my security camera
A blinking blue light indicates that the camera has lost connection to the Internet and is trying to reconnect. A red light indicates that the camera has been factory reset and is in pairing mode. Was this article helpful
Does the blue light on Ring camera mean someone is watching
The blue light on your Ring camera is not an indication that someone is watching you. The blue light flashing through the Ring camera means that the device has been configured. In other words, all the camera's security features are activated.
Is there a reset button on my ring floodlight
Locate the reset button atop the camera. Press and hold the reset button for 30 seconds. After releasing it, the status light located at the bottom will flash a few times indicating the camera is restarting. The camera settings are now restored to its factory defaults.
How do you fix motion detection on a Ring
To adjust the range of Motion Sensitivity:Open the Ring app.Tap the three lines (≡) on the top left of the dashboard.Tap Devices.Select the device you want to adjust.Go to Motion Settings.Use the slider to adjust detection sensitivity.
Why does my motion light go on and off
Flickering motion sensor lights can be caused by several things: A bad bulb or diode. A pretty straight-forward problem, even high-quality lights tend to go out eventually and sometimes even new ones can malfunction. A bad connection between the bulb or diode and the light fixture itself.
Does the Ring light turn on when motion is detected
Will the lights on my Floodlight Cam security camera turn on every time it detects motion No. The lights on the Floodlight Cam will only turn on for motion events when it's dark.
How do you fix a flickering floodlight
One thing that also can cause the flickering of the floodlights is, that there may be loose wiring at the fixture connection point. You can disconnect power to the fixture and re-tighten the wiring to make sure it's tight and secure, but if you're unsure how to do it, get a certified electrician to do it for you.
Are flickering lights a problem
Even if the flickering seems harmless, it could be a sign of a more serious underlying issue with your electrical wiring that could present a dangerous fire hazard to your home. Particularly if the flickering increases or changes in any way, call your electrician for an inspection just to be safe.
How do I get my Ring Floodlight back online
Unplug your router for 30 seconds and then plug it back in. See if your Spotlight Cam automatically reconnects.
How do I reset my Ring Floodlight WIFI
Reconnect to wifi in the Ring app:Tap menu (≡) (top left)Tap Devices.Tap Device Health.Tap Change Network.Tap Reconnect.Tap Continue and follow the prompts in the app to reconnect.Once your device is reconnected to wifi (which can take up to 30 minutes), check your wifi signal strength in Device Health under Network.
Does the blue light on ring camera mean someone is watching
The blue light on your Ring camera is not an indication that someone is watching you. The blue light flashing through the Ring camera means that the device has been configured. In other words, all the camera's security features are activated.
What does the flashing security light mean
That's the Security Indicator Light , and it's blinking, it's telling you that the car's security sytem is armed. When the car is locked and off, the Security Indicator Light will blink steadily. It will trigger shortly after the engine has been turned off and the key has been removed from the ignition.
How do you know if someone is watching live on Ring camera
Can you tell if someone is watching you on Ring If you see the infrared light turn on at night while the security camera is in Disarm Mode, someone else may be viewing your live feed. Change your router's password and ensure that video encryption is enabled on your Ring Camera.
Does ring light up when someone is watching
This indicates that the camera is powered on and recording. If the light is off, it's likely that no one is watching. There is no way of knowing if someone is watching you on the Ring camera. If the camera is active and the night vision is on, you can see the light turning on at night.
Why won t my Ring Floodlight stop flashing
Hitting the breaker, or switch, associated with this Floodlight Cam, waiting a moment, and turning it back on, might resolve this. If it does not, please perform a reset on the Floodlight Camera by holding the setup button for 20 seconds.
Why is my Ring motion sensor not detecting motion
Ensure that the batteries are installed. Press and hold the pinhole reset button. Continue pressing the button until the LED light turns red, then release. Re-add the Motion Detector to your Ring Alarm system.
How long does it take to reset Ring motion sensor
To reset the Detector, clear the detection area of anything that might create motion (such as you, your kids, or your pets) for a full three minutes. Click here for information on proper placement of your Motion Detector.
Why is my LED security light flashing
LED flood lights may flicker if there are voltage changes in the fixture's wiring. Current fluctuations are often to blame for the occasional flickering or flashing of an LED flood light. If your flood lights flicker when another appliance or electrical system is in use, a voltage fluctuation is likely to blame.
Why does my motion sensor go off randomly
Several factors can accidentally set off your motion sensors, including pets and any other activity from heat sources like vents, windows, stoves, or anything that causes a heat change near your sensor. The easiest way to test if your sensor is faulty is by putting a piece of paper in front of it for three days.
